Ebac FD100 Lumber Dryer

The Ebac FD100 Lumber Dryer is a packaged dehumidifier drying system for wood retailers and craftspeople who need to dry larger volumes of timber. It combines a wall-mounted dryer unit with the included STC1 Controller, featuring a proportional timer, thermostat, and electronic thermometer in a moisture-resistant casing. Two supplemental fans ensure even airflow throughout the stack, so mixed species and board thicknesses dry together down to as low as 6% moisture content. The FD100 mounts at ceiling height to preserve chamber space, ships with installation brackets, and is inexpensive to operate at roughly 1.2 kW per hour.

What's Included:

• Ebac FD100 Lumber Dryer Unit
• STC1 Controller (proportional timer, thermostat & electronic thermometer)
• Two Supplemental Airflow Fans
• Installation Brackets
• Owner's Manual
• PVC Tubing (16 mm I/D, approx. 10 ft.)
• Jubilee (Hose) Clip

Features

Handles Larger Loads
Dries a typical 7 m³ load and up to 8,875 board feet of 3 in. hardwood (740 cu. ft.) for wood retailers and busy workshops.

Dries to 6% Moisture Content
Operates effectively at low humidity to bring timber down to as low as 6% MC.

Two Supplemental Fans
Extra fans ensure even airflow throughout the stack for uniform drying.

STC1 Controller Included
Proportional timer, thermostat, and electronic thermometer in a moisture-resistant casing automate the drying cycle.

Mixed Species & Thicknesses
Dry different species and board thicknesses together in the same load.

Space-Saving Installation
Wall-mounted at ceiling height to minimize the space taken inside the drying chamber; installation brackets included.

Economical to Run
Inexpensive to operate at approximately 1.2 kW per hour.

What's Included

Included with Your Purchase:

• Ebac FD100 Lumber Dryer Unit
• STC1 Controller (proportional timer, thermostat & electronic thermometer)
• Two Supplemental Airflow Fans
• Installation Brackets
• Owner's Manual
• PVC Tubing (16 mm I/D, approx. 10 ft.)
• Jubilee (Hose) Clip

Specifications

• Product Type: Packaged dehumidifier lumber/timber drying system (for use in a drying chamber)
• Typical Load Capacity: 7 m³ (about 250 cu. ft.)
• Maximum Wood Load, Hardwood: 3,000 BF (1 in.) / 5,150 BF (2 in.) / 8,875 BF (3 in.)
• Maximum Wood Load, Softwood: 1,440 BF (1 in.) / 3,240 BF (2 in.) / 5,400 BF (3 in.)
• Airflow: 600 CFM
• Target Moisture Content: Down to 6% MC
• Maximum Operating Temperature: 122°F (50°C)
• Voltage: 220V, 1 Phase, 60 Hz
• Dryer Power: 1,100 W
• Heater Power: 1,500 W
• Maximum Amperage: 12 Amps
• Supplemental Fans: 2
• Controller: STC1 (proportional timer, thermostat & electronic thermometer) included
• Mounting: Wall-mounted, ceiling height (brackets included)
• Finish: Epoxy / vinyl coating with stainless steel condensate tray
• Dimensions (H x W x D): 33 in. x 43 in. x 12 in.
• Weight: 167 lbs.

FAQ

Q: Who is the FD100 for?
A: Wood retailers and craftspeople who need to dry larger volumes of timber than a small unit like the LD82 can handle.

Q: How much timber does it dry?
A: A typical load is around 7 m³. Maximum loads range from 3,000 board feet of 1 in. hardwood up to 8,875 board feet of 3 in. hardwood (about 250 to 740 cu. ft.), depending on species and board thickness.

Q: How dry can it get the wood?
A: Down to as low as 6% moisture content.

Q: Does it include a controller?
A: Yes. It comes with the STC1 Controller with proportional timer, thermostat, and electronic thermometer.

Q: How is it installed?
A: It is wall-mounted at ceiling height to save chamber space, and installation brackets are included.

Q: Is it costly to run?
A: No. It operates at approximately 1.2 kW per hour.

Resources

• Ebac FD100 Product Brochure
• Ebac FD100 Owner's Manual
• Ebac FD100 Spare Parts List
• Ebac FD100 Wiring Diagram
• Ebac FD100 Wiring Schematic